Full Frame > Ox End Dump Trailers

Overview

Trail Ox Series™ - Full Frame Elliptical "U" Body & Full Frame Square Bottom "L" Body.

Reduce your worries. Handle large loads with this heavy-duty frame design made to work in the worst conditions with top-notch engineering and materials built into every inch. Multiple configurations are available to meet your specific application requirements.

Two body styles in Elliptical "U" & Square Bottom "L"
Widths of 96" & 102"
Lengths of 24'-36'
Capacities up to 51.2 cubic yards
Continuous seam-welded design
Handles sand-to-large aggregates, riprap, and asphalt

Features

Full Frame Elliptical "U" Body:

Dimensions for Elliptical "U" body:

96" Wide / 84" Inside
Lengths of 24'-36'
Side heights of 36"-60" (in 6" increments)
Tailgate height 6" higher than sides
18 – 51.2 Cubic Yard Capacity (Elliptical "U" only)

Standard Features for Elliptical "U" Body:

3/16" high-tensile steel bulkhead and hoist well
3/16" Hardox AR450 steel used for sides with 1/4" Hardox AR450 floor
Cross-memberless, 10" I-Beam longsill with Flex Inhibitors
Conventional 7 gauge high-tensile steel, air-operated tailgate
Recessed/rubber grommet mounted LED lighting for side body, tail, clearance, and back up lights to meet Federal Standard 108
Heavy-duty hinges with 2-1/2" diameter CR pin and 1/8" NPT grease zerks
8" diameter, telescoping hoist
Steel, 16" x 26# wide flange I-Beam chassis
Continuous seam-welded design
Rubber flaps, front corner mounted
36" anti-sail, rear rubber mud flaps
2-speed landing gear
Single point-tandem suspension
2S/1M ABS braking system
Steel disc 22.5 x 8.25 wheels with 11R22.5 LRG, 14-ply tires
Epoxy primer and polyurethane top coat (chassis standard color is black)
2 Year Warranty

Full Frame Square Bottom "L" Body:

The Square Bottom "L" has many of the same standard features of the Elliptical "U" body with these key differences:

17.0 – 51.2 Cubic Yard Capacity (Square Bottom "L" only)
Mechanical – tandem suspension.
Vertical line posts with 10 gauge hightensile steel sides.
3/16" high-tensile steel floor.
Stacked, 4" structural cross-member with 6" I-Beam longsill frame design.

Options

Base Options:

For both Elliptical "U" Body & Square Bottom "L" Body:

102" body width
Sloped front in 3/16" or 1/4" AR450 Hardox steel with external hoist mount
Steel, 16" x 31# or 18" x 35# wide flange I-Beam chassis
Two way, side swing, and High-Lift tailgates
Tailgate coal chute (maximum of three)
Sealed tailgate kit
6" or 8" side boards in metal or wood
Full body height exterior/internal ladder located front driver's side
Dirt-shedding angle for side top rail, tailgate, and hoist well
Semi-auto or electric flip tarps, cable systems, or side roll tarps with choice of mesh or vinyl covers
Additional recessed/rubber grommet mounted LED lighting for sides and rear facing in rear posts to meet Federal Standard 108
In-cab wet line system/mounted control panel for hoist, tailgate, and tarp
9" diameter, telescoping hoist for body lengths of 30' thru 36'
Additional air tank for increased capacity
Under body vibrator
Rubber flaps with anti-sail brackets or steel gravel guards for mount in front of suspension
Lift axles in 13.5K or 20K steerable, or 20K rigid for body lengths of 28' thru 36'
4S/2M ABS braking system
Steel disc wheels: 22.5 x 8.25 or 24.5 x 8.25 in multi-tire configurations
Aluminum disc wheels: 22.5 x 8.25 or 24.5 x 8.25 in multi-tire configurations
Custom paint colors

For Elliptical "U" Body only:

1/4" Hardox AR450 steel sides
Multi-material selection for tailgate
Air ride tri-axle available for 28' thru 36' lengths
Air ride tandem axle available for all body lengths

For Square Bottom "L" Body only:

Multi-material selection for sides, floor plate, and tailgate
Stacked, I-Beam cross-member with 6" I-Beam longsill
Tandem single point, mechanical tri-axle, air ride tandem axle available for all body lengths